Camp kitchen & water

Is Coleman fuel the same as white gas?

Coleman fuel is a white gas, and MSR, which makes the best known white gas stoves, says so in one line. The trouble starts with the word naphtha. A can of VM&P naphtha can list the same chemical number as Coleman fuel and still boil about 80 degrees C higher and refuse to light from a match on a cool morning.

Updated 17 November 202614 min read

Yes. Coleman fuel is a white gas, and MSR, which makes the best known white gas stoves, says so in plain words: "Yes, Coleman fuel is a white gas." Any stove built for white gas takes it. What is not the same is the can of VM&P naphtha in a hardware store's paint aisle. Its own data sheets show a heavier, slower-lighting liquid that is sold as a solvent, not a fuel.

What white gas, Coleman fuel and naphtha mean#

White gas is a clear, highly refined petroleum liquid made to burn in pressurised stoves and lanterns. No ethanol appears on Coleman's ingredient list. You pump air into the stove's tank, and the pressure pushes the liquid to a hot tube, where it boils to vapour and burns at the jet. How that kind of stove compares with gas canisters, alcohol and wood is in camping stove types compared.

Coleman fuel is Coleman's brand of white gas. Its data sheet calls it Coleman Camp Fuel, and other brands sell the same class of fuel as SuperFuel (MSR), Crown Camping Fuel and Camplite.

Naphtha is a broad refinery word for light petroleum liquids, not one product. MSR uses it as another name for white gas, while paint and hardware shops use it for VM&P naphtha, short for varnish makers' and painters' naphtha. That is a solvent for thinning paint and varnish.

Two numbers on a safety data sheet decide most of this page, so they need plain meanings.

  • Boiling range. A fuel like this is a blend, so it boils over a range rather than at one point, and the lower the range, the more easily the fuel turns to vapour in the stove.
  • Flash point. The lowest temperature at which a liquid gives off enough vapour to catch from a flame. Below its flash point, a puddle of the liquid will not light from a match held over it.

A safety data sheet (SDS, older ones say MSDS) is the hazard document a chemical product's maker publishes. On a modern sheet, Section 3 lists what is in it, and Section 9 gives the boiling range and flash point.

What MSR and Coleman say#

MSR's support team answers the question directly. Asked whether Coleman fuel is "the same thing" as white gas, it says: "Yes, Coleman fuel is a white gas." It adds that Crown and Camplite also make white gas.

A longer MSR article on liquid fuels gives the other names that white gas goes by. White gas is "aka 'naphtha,' '100% light hydrotreated distillate,' or 'Coleman fuel'". Then comes the line that matters: "Not all brands are identical, but any stove that runs on white gas should burn Coleman fuel without issue."

So the maker of the WhisperLite and XGK stoves approves Coleman fuel for its white gas stoves in writing. Coleman, for its part, asks for its own fuel by name. Its Coleman-fuel-only lantern manual says other fuels "may shorten generator life, damage lantern".

The two brands do differ in one detail, and each maker states it on its own page.

  • Coleman fuel "includes a rust inhibitor to help prevent corrosion", says Coleman's lantern manual.
  • MSR SuperFuel has "No dyes or additives to solidify and cause clogs", says MSR. Its support article calls SuperFuel "more refined" and says it "reduces fuel line clogs".

MSR also warns about storage. Once a can is open, "the fuel starts to degrade", and a gallon of Coleman fuel that you rarely use "will degrade and possibly build up shellac" that can clog a stove's filters. That is MSR's case for buying small cans, not a case against Coleman fuel.

What the safety data sheets show#

MSR's word naphtha sends people to the paint aisle, and the data sheets show where that goes wrong. The table puts the fuels side by side, each from its maker's own sheet.

Composition and volatility from each product's safety data sheet. Dates are the sheet's revision or issue date
Product (sheet date)Main listed partOther listed partsBoilingFlash pointStated use
Coleman Camp Fuel (2022)CAS 68410-97-9, 60 to 100 percentPentane, isopentane, cyclohexene 5 to 10 percent each; hexane and two light fractions 1 to 5 percent eachAbove 38 degrees CBelow minus 18 degrees CRecreational fuel, stove or lantern
Coleman Camp Fuel (2007)CAS 68410-97-9, 100 percentCyclohexane up to 10 percentStarts above 38 degrees CBelow minus 18 degrees CCamp fuel (product name)
Crown Camp Fuel (2001)CAS 68410-97-9, 95 to 100 percentNone listed52, 110 and 137 degrees C listedMinus 18 degrees CCamp fuel (product name)
Zippo Lighter Fluid (2018)CAS 68410-97-9, 50 to 100 percentCAS 64742-49-0, 25 to 50 percentStarts above 35 degrees CBelow minus 6.5 degrees C"Fuel"
Lab Alley VM&P Naphtha (2019)CAS 68410-97-9 and/or two other naphthas, 90 to 100 percentOctane and heptane 5 to 10 percent each118 to 150 degrees C14 to 18 degrees CSolvent
Crown VM&P Naphtha (2008)CAS 64742-89-8, 100 percentNone listed115 to 162 degrees C10 degrees C (50 degrees F)Shipped as paint related material

Read the columns, not the chemical names. The three camp fuels and the lighter fluid all flash below freezing. Both VM&P sheets flash at 10 degrees C or above. The camp fuels and the lighter fluid start to boil above 35 to 52 degrees C. The VM&P sheets do not start to boil until 115 to 118 degrees C.

The parts lists say the same thing another way. NIST gives the boiling points of the named extras: Coleman's pentane boils at 36 degrees C, isopentane at 28 and cyclohexene at about 83. Lab Alley's VM&P lists heptane, which boils at 98 degrees C, and octane at 126. Coleman's sheet lists light extras. Lab Alley's VM&P sheet lists heavy ones.

The sheets are also dated. The Crown camp fuel sheet is from 2001 and the Crown VM&P one from 2008, so a can on sale now may differ. Even Coleman's own listing changed between 2007 and 2022. That is MSR's "not all brands are identical" in practice.

Why the same chemical number is not the same fuel#

The case for "VM&P is just white gas" rests on one fact. Lab Alley's VM&P sheet lists CAS 68410-97-9, the same number Coleman lists as its main part. A CAS number is a registry code for a substance, and for a pure chemical such as pentane, one number means one molecule.

This number is not that kind. The US EPA's Substance Registry Services files 68410-97-9 as a UVCB: a substance of unknown or variable composition. Its molecular formula is given as "Unspecified". The EU definition of the same entry describes hydrocarbons "predominantly in the range of C6 through C9 and boiling in the range of approximately 3°C to 194°C".

That range is about 190 degrees wide, so a light cut from the bottom of it and a heavy cut from the top can both carry the number. Coleman's light extras sit near the bottom of it. Lab Alley's VM&P, by its own boiling range of 118 to 150 degrees C, sits in the upper half.

Lab Alley's listing is also hedged. It reads 68410-97-9 "and/or" two other naphtha numbers, so a given batch may not contain 68410-97-9 at all. Crown's VM&P lists only 64742-89-8, a different number.

So both camps in the forum threads have something real. "Coleman fuel is naphtha" is true in MSR's broad sense. "Paint thinner naphtha is not stove fuel" is true by the data sheets. The word is shared, but the fuel in the can is not.

A worked case: one maker, two cans#

Crown makes this easy to see, because one company, Packaging Service Co., sells both cans. MSR names Crown Camping Fuel as a white gas, and the same firm sells Crown VM&P Naphtha as a paint related material.

Take a cool autumn morning at 5 degrees C (41 degrees F). Suppose a white gas stove's priming cup is filled from each can in turn. Walked through the two sheets:

  1. Flash point against the air. Crown Camp Fuel flashes at minus 18 degrees C. At 5 degrees C it sits 23 degrees above its flash point, so it gives off enough vapour to light from a match. Crown VM&P flashes at 10 degrees C, so at 5 degrees C it sits 5 degrees below its flash point. By the definition of flash point, it does not give off enough vapour to light from a match.
  2. Boiling against the stove. The camp fuel's sheet lists 52, 110 and 137 degrees C for its boiling range. The VM&P begins to boil at 115 degrees C and ends at 162. So all of it boils at temperatures the camp fuel reaches only near or past the end of its range.
  3. Weight. The camp fuel's specific gravity is 0.700 and the VM&P's 0.75. A 1 litre bottle holds about 700 g of one or 750 g of the other, a difference that does not matter.
  4. The label. One can is sold for camp stoves and lanterns, and the other ships as paint related material. Neither MSR nor Coleman names VM&P naphtha as a fuel in anything read for this page.

Walked through, the figures say the same firm's two cans are two different fuels. Nobody tested the VM&P in a stove for this page, and nothing here predicts how a given stove would run on it. The point is narrower: the fuel MSR approves and the solvent beside it on the shelf are not the same liquid, even from one maker.

Which fuels can go in a white gas stove#

Each row restates a ruling made above, with its basis.

Fuels for a white gas stove, from the rulings and sources on this page
FuelIn a white gas stove?WhyBasis
Coleman Camp FuelYes"Coleman fuel is a white gas"MSR support; Coleman SDS
MSR SuperFuelYesWhite gas with no additivesMSR product page and support
Crown or Camplite camping fuelYesNamed by MSR as white gasMSR support
VM&P naphtha (paint aisle)No, not as a white gas swapBoils at 115 to 162 degrees C, flashes at 10 to 18; sold as a solvent; no stove maker read names itCrown and Lab Alley VM&P sheets
Lighter fluid (Zippo type)Not approvedClose to camp fuel on its sheet, but no stove maker read names itZippo SDS
Unleaded car gasolineOnly if the stove's manual names itMSR: "not necessarily interchangeable" with white gasMSR support; unleaded page

Lighter fluid needs one more line. Zippo's sheet lists the same main number as Coleman fuel, at 50 to 100 percent. It starts to boil above 35 degrees C and flashes below minus 6.5. On paper it is the nearest to camp fuel of the non-camp fuels on this page. But the only stated use is "Fuel", for Zippo's own lighters, and no stove maker read here approves it, so it is not a fuel this page can approve either.

Unleaded is its own question, with its own answer. Coleman's Dual Fuel models allow it, at the cost of generator life, and its Coleman-fuel-only models say never. That is set out in can you use unleaded gas in a Coleman stove.

Check the can before you pour#

Five checks, and all you need is the can, its label and a phone.

  1. Read the front. "Camp fuel", "camping fuel" or "white gas" is the class MSR approves. "VM&P naphtha" or "paint thinner" is a solvent.
  2. Find the safety data sheet. Search the product name and "SDS", since retailers and makers post them.
  3. Check Section 1, the stated use. Coleman's says "Recreational Fuel, Stove or Lantern". Lab Alley's VM&P says "Solvent".
  4. Check Section 9, the flash point. The camp fuels above flash at minus 18 degrees C or lower. A flash point of 10 degrees C or more is where the VM&P sheets sit, not white gas.
  5. Check your stove's manual for the fuels it names. The manual overrides this page, and if it names a fuel not listed above, use that.

If you are flying to a trip and buying fuel where you land, the same checks apply abroad. Fuel never goes in your luggage, as can you take a camping stove on a plane explains.

Common mistakes#

Reading "naphtha" as a product name. MSR uses it as a class name for white gas, while the paint shop uses it for a heavier solvent. Same word, different liquid.

Trusting a matching CAS number. 68410-97-9 covers a range about 190 degrees C wide. Check the boiling range and flash point in Section 9, not just the number in Section 3.

Buying a gallon for one trip a year. MSR says opened fuel degrades and can leave shellac in the pump filters. Buy the size you will use. For keeping fuel and stoves between trips, see storing gear between trips.

Treating SuperFuel and Coleman fuel as rivals. Both are white gas. SuperFuel has no additives and Coleman fuel has a rust inhibitor, and MSR approves Coleman fuel in its stoves.

Assuming white gas weighs like water. It does not: Coleman's sheet gives a relative density of about 0.69, so a litre weighs about 690 g. Fuel weight for a trip is worked through in how much stove fuel to carry.

Pouring from a mislabelled bottle. Keep white gas in its own can or a marked fuel bottle, because a bottle of VM&P or unleaded in the same colour is easy to grab in the dark.

What this answer does not cover#

This page compares safety data sheets and maker statements. It does not test any fuel, and nobody ran a stove on VM&P naphtha or lighter fluid for it. The sheets are snapshots: the Crown sheets date from 2001 and 2008, and a can on sale today may list different parts. Brands outside the US, and fuels sold under other names (such as "benzin" or "Shellite"), were not read, so check their own sheets. Kerosene, diesel and alcohol are separate fuels for separate jets or stoves, not white gas. Every fuel here is highly flammable and gives off carbon monoxide when burned, so fill outdoors, away from flame, and never run a liquid fuel stove in a tent. Before you fill, confirm the fuel your own stove's manual names.

Frequently asked questions#

Is Coleman fuel the same as white gas?#

Yes. MSR's support team says "Coleman fuel is a white gas", and that any stove that runs on white gas should burn it without issue. Coleman's 2022 safety data sheet lists a light hydrotreated distillate as 60 to 100 percent of the fuel, plus pentane, isopentane, cyclohexene and hexane. It flashes below minus 18 degrees C, and its stated use is stoves and lanterns.

Is white gas the same as naphtha?#

In the broad sense, yes: MSR lists naphtha as another name for white gas. But the can labelled VM&P naphtha in a hardware store is a heavier solvent. Two VM&P data sheets give it a boiling range of 115 to 162 degrees C and a flash point of 10 to 18 degrees C. Coleman fuel starts boiling above 38 and flashes below minus 18.

Can you use VM&P naphtha in a Coleman stove?#

Not as a substitute for white gas. No Coleman or MSR document read for this page names VM&P naphtha as a fuel, and its data sheets list it as a solvent or paint material. It flashes at 10 to 18 degrees C, so on a cool morning it will not light from a match. Use camp fuel, or a fuel your stove's manual names.

Can you use lighter fluid in a camp stove?#

No stove maker read here approves it. On paper, Zippo lighter fluid is close to Coleman fuel: its sheet lists the same main part, a boiling range starting above 35 degrees C and a flash point below minus 6.5. But its sheet gives its use only as "Fuel", and it is sold for lighters.

What is the difference between MSR SuperFuel and Coleman fuel?#

Both are white gas. MSR says SuperFuel has "No dyes or additives" and is more refined, which it says reduces clogs. Coleman says its fuel "includes a rust inhibitor to help prevent corrosion". MSR approves Coleman fuel in its own white gas stoves, so either works, and the bigger factor is freshness, since MSR says opened fuel degrades.

What is a substitute for white gas?#

Another brand of white gas: MSR names Coleman, SuperFuel, Crown and Camplite camping fuel. After that, it depends on the stove: Coleman Dual Fuel models and MSR multi fuel stoves take unleaded gasoline, with more upkeep. MSR's multi fuel stoves take kerosene on the right jet. VM&P naphtha and lighter fluid are not named by any maker read here.

Does Coleman fuel go bad?#

It can, once opened. MSR says that after you open a container, "the fuel starts to degrade", and a gallon you rarely use can build up shellac that clogs a stove's pump filter. Coleman's lantern manual says to rinse the tank with fresh fuel to clear gum and moisture. Neither gives a shelf life in months, so buy the size you will use.

Standards, sources and further reading

  1. Cascade Designs (MSR) support, *I can't find white gas anywhere; is Coleman fuel the same thing?*, updated 18 November 2024 (read through the help centre API). "Yes, Coleman fuel is a white gas"; names MSR SuperFuel, Crown Camping Fuel and Camplite Camping Fuel as white gas.
  2. Cascade Designs (MSR) support, *What type of fuel can I use in my liquid fuel stove?*, updated 7 July 2025. White gas "aka 'naphtha,' '100% light hydrotreated distillate,' or 'Coleman fuel'"; "Not all brands are identical, but any stove that runs on white gas should burn Coleman fuel without issue"; SuperFuel "is free of additives"; an opened gallon can "will degrade and possibly build up shellac"; white gas and auto gas "are not necessarily interchangeable".
  3. MSR (Cascade Designs), *SuperFuel*, product page. "Tested to be 100% pure"; "No dyes or additives to solidify and cause clogs"; 1 qt (946 mL).
  4. The Coleman Company, *Coleman Camp Fuel, Safety Data Sheet*, version 5.1, revised 7 April 2022. Use: "Recreational Fuel, Stove or Lantern". CAS 68410-97-9 at 60 to 100 percent; pentane, isopentane and cyclohexene 5 to 10 percent each; hexane, CAS 64742-47-8 and CAS 64742-49-0 at 1 to 5 percent each. Boiling point above 38 degrees C; flash point below minus 18 degrees C; relative density about 0.69.
  5. HOC Industries for Coleman, *Coleman Camp Fuel, Material Safety Data Sheet*, made 12 February 2004, revised 19 June 2007. Light hydrotreated distillate, CAS 68410-97-9, 100 percent; cyclohexane up to 10 percent; flash point below 0 degrees F (minus 18 degrees C), Tag closed cup; initial boiling point above 38 degrees C; specific gravity 0.7.
  6. Packaging Service Co., *Crown Camp Fuel, Material Safety Data Sheet*, 28 November 2001. 95 to 100 percent light hydrotreated distillate, CAS 68410-97-9; boiling range listed as 52, 110 and 137 degrees C; flash point minus 18 degrees C (TCC); specific gravity 0.700; "Water-White".
  7. Packaging Service Co., *VM&P Naphtha, Material Safety Data Sheet*, 1 August 2008. 100 percent V. M. & P. Naphtha, CAS 64742-89-8; boiling point 115 to 162 degrees C; flash point 50 degrees F (10 degrees C), PMCC; specific gravity 0.75; shipped as "UN1263, PAINT RELATED MATERIAL".
  8. Lab Alley, *VM&P Naphtha, Safety Data Sheet*, version 4.10, revised 1 September 2019. Recommended use: "Solvent". CAS 68410-97-9 and/or 64742-49-0 and/or 64742-89-8 at 90 to 100 percent; octane and heptane 5 to 10 percent each. Boiling range 118 to 150 degrees C; flash point 14 to 18 degrees C, closed cup; relative density 0.74 to 0.76.
  9. Zippo Manufacturing Company, *Zippo Lighter Fluid, Safety Data Sheet* (EU format, revised 18 January 2018; retailer-hosted copy). Application: "Fuel". CAS 68410-97-9 at 50 to 100 percent; CAS 64742-49-0 at 25 to 50 percent. Initial boiling point above 35 degrees C; flash point below minus 6.5 degrees C; density 0.7 g/cm3 at 20 degrees C.
  10. The Coleman Company, Lantern model 3000000101, instructions (© 2007), Internet Archive PDF. Coleman fuel "includes a rust inhibitor to help prevent corrosion"; other fuels "may shorten generator life, damage lantern".
  11. US EPA, *Substance Registry Services*, record for CAS 68410-97-9: category class UVCB, molecular formula "Unspecified".
  12. NextSDS, *CAS 68410-97-9*, reproducing the EU inventory definition for EC 270-093-2: hydrocarbons "predominantly in the range of C6 through C9 and boiling in the range of approximately 3°C to 194°C".
  13. NIST Chemistry WebBook, SRD 69, normal boiling points: pentane 309.2 K, isopentane 301.1 K, cyclohexene 356 K, heptane 371.5 K, octane 398.7 K.

How this page is made. Every number here is either a published standard, a physical constant, or arithmetic we show in full so you can check it. Read our evaluation method and editorial standards, or tell us we got something wrong.

Last reviewed and updated 17 November 2026.