Camp kitchen & water

Do all gas canisters fit all camping stoves?

Small camping gas comes in five fittings, and only one of them is shared across brands: the screw-on canister with a 7/16 inch threaded valve. An MSR, Jetboil, Primus, Snow Peak or Coleman screw-on can fits any stove built for that thread. A Campingaz click-on cartridge, a pierceable can, a butane cassette and a 1 lb propane bottle each fit only their own kind of stove. The thread is half the question; the gas inside is the other half.

Updated 18 November 202613 min read

No. Only one kind of camping gas can is shared across brands: the screw-on canister with a 7/16 inch threaded valve. Any of those, from MSR, Jetboil, Primus, Snow Peak or Coleman, fits any stove built for that thread. Four other fittings exist. Campingaz click-on cartridges, pierceable cans, butane cassettes and 1 lb propane bottles each fit only their own kind of stove.

What "fits" means: the valve, the thread and the gas#

A gas canister here means a small, single-use steel can of liquefied gas made for camping stoves and lanterns. The fuel inside is a liquid under pressure. The stove burns the gas that boils off the top.

Every canister has a fitting: the part on top that joins it to the stove. Most of this question is about fittings, so here are the five you will meet.

  1. Screw-on (threaded valve). A threaded neck with a spring valve inside. The stove screws on and presses the valve open. Unscrew it and the valve closes. The valve is the Lindal B188, named for its maker. Its thread is 7/16 inch UNEF, a fine, standard US thread size.
  2. Campingaz Easy Clic (CV). A self-sealing valve that clicks into Campingaz appliances. There is no 7/16 inch thread to screw onto.
  3. Pierceable. A sealed can with no valve at all. The stove punches a hole in the top as you fit it, and it stays on until the can is empty.
  4. Butane cassette. A long can that lies on its side in a tabletop stove. A notch on its collar lines up with a guide in the stove. Most are butane, though Campingaz's CP 250 holds isobutane.
  5. 1 lb propane bottle. The green or blue cylinder for camp grills and lanterns. Its neck has a much larger thread, the CGA600 fitting.

The other half of "fits" is the gas. Canisters hold a blend: propane mixed with isobutane or with plain butane (chemists call it n-butane). The three behave very differently in the cold. A thread that fits does not tell you which blend is inside.

Why "EN 417" confuses people#

EN 417 is the European standard for these single-use metal gas cans. Many people use "EN 417" as a name for the screw-on canister. That is a loose use. Wikipedia's EN 417 page says the standard covers cartridges "with or without a valve", including valveless pierceable cans. A second Wikipedia page, on gas connections, goes further: EN 417 "does however not specify any connectors".

Campingaz shows it plainly. It calls its pierceable C206 GLS "compliant to the new European standard EN 417:2012". That can will not fit a screw-on stove. So "EN 417" on a label is a promise about how the can is built. It is not a promise about the thread.

Which canisters fit which stoves#

Here is each fitting, what it fits, and who says so.

The five small-gas fittings, from the maker pages and references in the source list
FittingExamplesFitsBasis
Screw-on, Lindal B188, 7/16 inch UNEFMSR IsoPro, Jetboil JetPower, Primus, Snow Peak, Coleman C300Any stove made for that thread, across brandsJetboil FAQ; MSR support; Coleman C300 page; Wikipedia
Campingaz Easy Clic (CV)CV 300 Plus, CV 470 PlusCampingaz Easy Clic and Easy Clic Plus appliancesCampingaz CV pages
Pierceable, no valveCampingaz C206 GLSStoves made for that can; stays on until emptyCampingaz C206 page; Wikipedia EN 417
Butane cassetteCampingaz CP 250, Iwatani BU-6Cassette (tabletop) stoves; Iwatani names its own can onlyCampingaz CP 250 page; Iwatani ZA-3HP manual
1 lb propane, CGA600, 1 inch 20 UNEFDisposable and refillable 16.4 oz cylindersPropane camp stoves, grills and lanternsWikipedia connections page; Flame King

Only the first row crosses brands. The others are closed systems, each built around one maker's can or one class of stove.

The thread size: 7/16 inch, not 3/8#

The screw-on thread is 7/16 inch UNEF, 28 threads per inch, 11.1 mm across. That is the figure in both Wikipedia references for the Lindal B188 valve.

MSR's support page gives a different figure. It says the threads are "roughly 3/8" or about 6 mm in diameter". Those two numbers do not agree with each other. 3/8 inch is 9.5 mm. 6 mm is about 1/4 inch. Neither matches 7/16 inch.

Which is right? The 7/16 inch figure is the one tied to a named valve and a named thread standard. MSR's line is a rough description with two numbers that cannot both be true. So this page uses 7/16 inch. The Lindal maker page was not readable to us, so the figure rests on the two Wikipedia references. The kitchen check below lets you confirm it on your own can.

The 1 lb propane bottle is far bigger: 1 inch across, 20 threads per inch (25.4 mm). Nobody mistakes the two once they are side by side. That neck is the CGA600 fitting; Flame King says its refillable bottle with it "fits all appliances that today's non-refillable tanks work with".

Brand to brand: MSR, Jetboil, Primus, Snow Peak and Coleman#

Among screw-on canisters, the makers agree that the fitting is shared. They differ on whether they will vouch for a can that is not their own.

Jetboil. Its FAQ says: "Jetboil is compatible with valves made to the EN417 specification". It names Brunton, Gigapower (Snow Peak's fuel), MSR, Primus and Snow Peak as fuel with "the same mixture and valve as ours". It also says it "cannot claim safe operation" with any can but its own JetPower.

MSR. Its answer is "Technically yes", if the can is certified to EN 417 and holds "an 80% isobutane / 20% propane mix". Then it adds: "But we don't recommend it." MSR says its stoves are tuned for its own IsoPro fuel.

Coleman. Its European C300 Performance page describes a "threaded self-sealing cartridge". It says the can fits "all Coleman resealable appliances". The blend is listed as 70/30 butane/propane. The same page gives the gas as both 220 g and 240 g, so this page uses neither.

Primus and Snow Peak. Both sell screw-on canisters, and Jetboil names both as the same valve.

So the thread is shared, and so is the "use our own" line. No maker read here forbids another brand's screw-on can. None will guarantee one either.

The blend: does 70/30 butane work where the maker says 80/20 isobutane?#

Here the "fits" question becomes a "works" question. Three gases are in play, and their pressure in the cold is what counts. Vapour pressure is how hard the gas pushes out of the can. It is set by the liquid's temperature. Gauge pressure is that push minus the air around it. At zero gauge, no gas flows.

From NIST data, pure gas at 0 degrees C (32 degrees F) gives this much gauge pressure:

  • Propane: 3.73 bar.
  • Isobutane: 0.56 bar.
  • n-butane: 0.02 bar, almost nothing.

A fresh can is a mix. We worked both common blends through Raoult's law, a model that treats the blend as an ideal mix. Each gas adds its own pressure in proportion to its share of the liquid.

Our Raoult's law model on NIST saturation pressures, by mass blend, referenced to 1.013 bar of air
Blend, fresh canGauge pressure at 0 degrees CAt minus 10 degrees C
80/20 isobutane/propane (MSR's condition)1.34 bar0.66 bar
70/30 butane/propane (Coleman C300)1.36 bar0.68 bar
Pure isobutane (propane all burned off)0.56 bar0.07 bar
Pure n-butane (propane all burned off)0.02 barnone

The fresh cans push about the same. The extra propane in the butane blend makes up for the weaker butane.

The difference comes later. Propane boils off first, so the liquid left behind gets poorer in propane as you cook. Near the end, a 70/30 butane can is close to pure n-butane. At 0 degrees C that gives almost no pressure. An 80/20 isobutane can ends near pure isobutane, which still gives 0.56 bar. Canister stoves in the cold works this fading through step by step.

So the label matters most on a cold morning with a part-used can. In summer, a fresh can of either blend will run a screw-on stove the same.

A worked case: one stove, three cans on a shop shelf#

Take an MSR stove with a screw-on mount, and suppose you have run out of IsoPro on a trip in France. The shop has three cans. Walk through each one.

Can 1: Coleman C300 Performance. It is a "threaded self-sealing cartridge", so the thread fits. MSR's condition was 80/20 isobutane/propane. This can is 70/30 butane/propane, so it is outside what MSR said should work. From the table above, a fresh can pushes about the same as MSR's blend at 0 degrees C. The last third will be weaker in frost. At 10 degrees C or warmer, n-butane alone still gives 0.47 bar, so the tail will burn, if slowly. Verdict: fits, and outside MSR's stated blend.

Can 2: Campingaz CV 470 Plus. Campingaz lists it "for use with Campingaz Easy Clic PLUS and Easy Clic appliances". It has no 7/16 inch thread to screw onto. Verdict: does not fit. MSR says no adapter.

Can 3: Campingaz C206 GLS. It is pierceable, with no valve at all. It carries the EN 417:2012 mark, which is why it can look right. Verdict: does not fit. The EN 417 mark is not enough. MSR adds: "Only the standard lightweight backpacking cannisters will work." Those are the screw-on kind.

Worked through, one of three cans fits, and that one fits with a caveat. The other two would only "fit" through an adapter MSR says you cannot use.

What about adapters?#

Adapters are where the systems meet, and the makers are clear about them.

MSR's support page: "You cannot use an additional adapter to use a different type of fuel or cannister type. Only the standard lightweight backpacking cannisters will work." That rules out any adapter on an MSR stove.

The one adapter listing read for this page, a CAMPINGMOON Z20, goes the other way. It turns "a standard EN417 Lindal valve camping cartridge" into a CGA600 feed, so a screw-on can runs a 1 lb propane appliance. Its own warning matters. It is "not equipped with a check valve (self-sealing valve), so it will leak when the gas canister is not connected to a device". Fit it to the stove first, then the can. It is for outdoor use only.

Two systems cannot be bridged by design. A pierceable can "can't be disconnected" once fitted, Campingaz says, so it cannot move to another stove part-used. And a cassette stove like Iwatani's tells you to use only "Iwatani Butane Fuel". An adapter there is outside the maker's own rule.

Adapters also change only the fitting. They do not change the gas. Joining a propane bottle to a butane stove multiplies the pressure on its valve by about seven; can you use propane in a butane stove? gives the figures.

How to check a canister before you buy it#

Five checks, done in a shop or a kitchen.

  1. Look for a thread. A screw-on can has a threaded metal neck around a small centre pin. No thread means it is not a screw-on can, whatever the label says.
  2. Measure it. A ruler across the outside of the thread should read about 11 mm. A reading near 25 mm is a 1 lb propane bottle. Nothing close to either means another system.
  3. Read the fitting words. "Easy Clic" or "CV" means Campingaz click-on. "Pierceable" means no valve. "For Bistro type" or a cassette shape means a tabletop stove.
  4. Read the blend. Look for propane plus isobutane, or propane plus butane, with a ratio. For cold trips, the isobutane blend holds pressure longer as the can empties.
  5. Read your stove's manual. If it names one fuel, that is the maker's rule. Fitting does not override it.

When a can is partly used, weigh it first. How much gas is left in a canister has the empty weights by brand.

Common mistakes#

Trusting "EN 417" on the label. A pierceable C206 carries it too. Check for the thread.

Thinking 3/8 inch is the thread size. It is 7/16 inch. A 3/8 inch fitting bought on that figure will not match.

Forcing a cross-threaded can. A screw-on can should turn on by hand, straight down. Leaks at the joint come from dirt and cross-threading, as covered in leaving a canister on the stove.

Reading "butane/propane" as the same as "isobutane/propane". Fresh, they push about the same. Near empty in frost, the butane can gives almost nothing.

Fitting a screw-on can to an adapter before the stove. The CAMPINGMOON listing says the gas will leak.

Carrying a pierceable can to swap between stoves. It cannot come off until it is empty.

What this answer does not cover#

This page covers the five small-gas fittings and the brands named, from maker pages read for it. Several of those pages are Internet Archive copies from 2020 to 2022, because Campingaz and Coleman sites refuse fetchers; check the can in your hand. It does not test any stove, can or adapter. Nobody here fitted one can to another stove; the shared thread is what the makers and the two Wikipedia references say. The 7/16 inch figure rests on Wikipedia, since the Lindal page could not be read. The blend pressures are a model, not a measurement, and real cans vary. Coleman's US screw-on line and GSI's canisters were not read, so neither is named. We read no adapter for Campingaz CV, pierceable or cassette cans, so none is described. A can that fits is not approved: your stove's manual is the rule, and no maker read here guarantees another brand's fuel. Bulk propane tanks and refillable systems are outside it. Never test a fit near a flame, and never light any of these stoves in a tent or closed space. For choosing a stove type in the first place, start with camping stove types compared.

Frequently asked questions#

Can I use MSR fuel in a Jetboil?#

Yes, the fit is the same. Jetboil's FAQ says its stoves take valves made to the EN417 specification, and it names MSR fuel as having "the same mixture and valve" as JetPower. Jetboil also says it cannot claim safe operation with any can but its own. MSR IsoPro is 80/20 isobutane/propane.

Can I use Jetboil fuel in an MSR stove?#

Yes, by MSR's own test. MSR says another brand works "technically" if it is certified to EN 417 and holds an 80/20 isobutane/propane mix. MSR still recommends its own IsoPro, and says it cannot guarantee another can's quality or your stove's performance on it.

Does a Campingaz cartridge fit an MSR or Jetboil stove?#

The CV click-on cartridges do not. Campingaz lists the CV 300 Plus and CV 470 Plus for its Easy Clic and Easy Clic Plus appliances, and they have no 7/16 inch thread. The pierceable C206 does not fit either. MSR says no adapter may be used to change canister type.

What thread size is a camping gas canister?#

A screw-on camping canister uses the Lindal B188 valve: 7/16 inch UNEF, 28 threads per inch, about 11.1 mm across. MSR's support page calls it "roughly 3/8" or about 6 mm", but those figures disagree with each other and with 7/16 inch. A 1 lb propane bottle is 1 inch, 20 threads per inch.

Are all EN 417 canisters the same?#

No. EN 417 covers single-use metal gas cans with or without a valve, and it sets no connector. Screw-on canisters and valveless pierceable cans can both be EN 417. Only the screw-on type, with the Lindal B188 valve, fits the stoves sold by MSR, Jetboil, Primus and Snow Peak.

Does Coleman gas fit other stoves?#

Coleman's C300 Performance is a threaded self-sealing cartridge, so it fits stoves made for screw-on canisters. Its blend is 70/30 butane/propane, not the 80/20 isobutane/propane MSR names. Coleman's 1 lb propane bottles use the larger CGA600 thread and fit only propane appliances.

Is butane/propane the same as isobutane/propane?#

Not in the cold. Fresh, our model gives a 70/30 butane/propane can and an 80/20 isobutane/propane can about 1.35 bar at 0 degrees C. As propane burns off first, the butane can ends near 0.02 bar, while the isobutane can still gives 0.56. In warm weather the difference is small.

Standards, sources and further reading

  1. Cascade Designs (MSR) support, *Can I use another Brand of Canister Fuel with MSR Stoves?*, updated 1 October 2025 (read through the help centre API). "Technically yes, as long as it is a canister that's certified to EN 417 with an 80% isobutane / 20% propane mix. But we don't recommend it"; "You cannot use an additional adapter to use a different type of fuel or cannister type"; "The threads are roughly 3/8" or about 6 mm in diameter."
  2. Jetboil, *Frequently asked questions* (PDF, dated June 2021). "Jetboil is compatible with valves made to the EN417 specification"; it cannot "claim safe operation with any canister other than our Jetpower brand of fuel"; Brunton, Gigapower, MSR, Primus and Snowpeak fuel "has the same mixture and valve as ours".
  3. Wikipedia, *EN 417*. EN 417 covers non-refillable metal LPG cartridges "with or without a valve"; the name is used loosely for cartridges with the 7/16 inch UNEF threaded valve, correctly the Lindal B188 valve; valveless pierceable canisters are EN 417 cartridges too. The article carries an original research notice.
  4. Wikipedia, *Propane, butane, and LPG container valve connections*. EN 417 "does however not specify any connectors"; Lindal B188: 7/16 inch UNEF, 11.1 mm, 28 threads per inch; 1 lb (16 oz) propane bottle: CGA600, 1 inch 20 UNEF, 25.4 mm, right hand; "Bayonet camping" cartridges have no thread.
  5. Coleman (Europe), *C300 Performance gas cartridge*, Internet Archive capture of 12 August 2020. "220g (70/30) butane/propane gas mixture in threaded self-sealing cartridge with safety valve"; "compatible with all Coleman resealable appliances"; the same page also lists "Gas in g: 240 g".
  6. Campingaz, *CV 470 Plus*, Internet Archive capture of 16 October 2021. "For use with Campingaz Easy Clic PLUS and Easy Clic appliances"; self-sealing valve; "Can be easily disconnected and reconnected even when not empty"; 450 g butane/propane mix. The CV 300 Plus page (capture of 23 May 2022) carries the same text for 240 g.
  7. The Camping Store, *Campingaz CV470 Plus gas cartridge*, retailer listing. 80 percent butane, 20 percent propane, 450 g; Easy Clic Plus system; "Always check that your appliance is explicitly compatible".
  8. Campingaz, *C206 GLS*, Internet Archive capture of 20 January 2022. "Pierceable cartridges can't be disconnected once they've been plugged into an appliance"; Gas Lock System, "compliant to the new European standard EN 417:2012"; 190 g butane/propane mix.
  9. Campingaz, *CP 250*, Internet Archive capture of 16 October 2021. "Cartridge for Bistro type stoves"; 220 g isobutane; 6.9 x 18 cm.
  10. Iwatani, Instruction Manual, Portable Butane Gas Stove ZA-3HP (PDF). Canister notch and receiving guide; fuel Iwatani Butane Fuel BU-6, "only use Iwatani fuel as other brands may cause poor operation or safety issues"; cylinder must be DOT 2P or 2Q.
  11. Flame King, *1lb Refillable Cylinder + Kit, 16.4 oz.*, product page. CGA600 connection that "fits all appliances that today's non-refillable tanks work with".
  12. CAMPINGMOON, *Z20 Grill Propane Gas Stove Adapter*, retailer listing. Converts "a standard EN417 Lindal valve camping cartridge to a CGA600 connection"; "not equipped with a check valve (self-sealing valve), so it will leak when the gas canister is not connected to a device"; outdoor use only.
  13. NIST Chemistry WebBook, SRD 69, saturation pressure tables for propane (C74986), n-butane (C106978) and isobutane (C75285). Absolute pressure at 0 degrees C: 4.7446, 1.0323 and 1.5696 bar; at minus 10 degrees C: 3.4528, 0.69552 and 1.0845 bar.

How this page is made. Every number here is either a published standard, a physical constant, or arithmetic we show in full so you can check it. Read our evaluation method and editorial standards, or tell us we got something wrong.

Last reviewed and updated 18 November 2026.